Search results

No. Those in settings are selections and percentage. Calibration and sensititivity is another thing, necessary for almost every kind of electronic or mechanical device that exists in this world.

ColorVU G5 Acusense does not have an option in settings to Calibrate while it should. Same way this does not have an option to adjust all kind of Detection sensitivities, Normal or Smart.

Can you explain why Calibration does not exist on Basic Settings for ColorVUs. But this exists as someone can see by a high end NVR. But is not accessible from basic settings GUI either web or iVMS or Batch config tool

I 've seen what you mean by SDK ti ISAPI, sometimes when plugins not installed correctly on iVMS4200 you see the Batch configuration tool GUI, but advanced Function GUI, if you manage quickly to get a screenshot, is different and possibly locked.

No. Sometimes there is something different. But this must be unlocked to access. For example my DS-KV6113WPE1(A), Advanced Function is accessible and some things can be set only from there. Special characters on wifi password not recognised in Basic Settings and CCD Day/Night Switch Mode, where...

Possibly they are fixing something. I hope it is the Enable Dynamic Analysis for Motion so that I finally install this GUI 5 :-)

v5.7.17_240731 today went back to v5.7.17_240606

I installed this yesterday. But I cannot test the Acusearch improvements without v5.7.17 on my G5s. Installed again v5.7.17 on one of G5s but the problem with Motion search by Drawing area(by Rules) remains the same. No Motion Events found in Playback - Event - Smart Search - Draw Motion by...

With release notes..... No other NXI-K model shows this firmware for the time being. Not even DS-7608NXI-K2/8P or NXI-K4 https://www.hikvision.com/en/products/IP-Products/Network-Video-Recorders/Pro-Series/ds-7608nxi-k2/

Experimenting today and after going back from firmware v5.7.17 to v5.7.15 for G5 platform noticed the following for DS-2CD2047G2H-LIU and DS-2CD2047G2-L connected on DS-7608NXI-K2 : iVMS4200 Remote Playback - Camera select for play - VCA Search - Enable Motion Detection, by drawing 100% of...

Yes, but the issue that arose after v5.7.17 seems to be related with the Dual VCA and/or Save Camera VCA Data, which has to do with the NVR ability to record/mark the VCA Events on timeline by drawing a box or grid(by rules). I have exactly the same camera connected on DS-7608NXI-K2 NVR

Yes, the issues with Motion remain the same at least for me. Went back once again to 5.7.15, but my fault was that I did not test more. I 'll try again by reinstalling and check above mentioned by @JB1970. As I said on another post, possibly Intelligent Search option, even if not enabled, causes...

Hi @JB1970 Did you check your NVR GUI? Is VCA by Camera enabled after updating the camera?

Hi @Armano38 What is your NVR model? I do have the same issue with this new firmware

Hi Tested, by making a mistake on ip, for both ColorVu. The Hybrid one and the non-Hybrid. DS-2CD2047G2H-LIU and DS-2CD2047G2L. For both of them there are once again no results in By Rules Motion Search on my DS-7608NXI-K2(drawing search grid boxes). Everything else works fine and also all...

Hi @JB1970 I have seen that but not tried yet. Yes the firmware file size is smaller. I hope I can roll back if by Rules Search VCA uploading issue remains the same for my NXI-K NVR ..... I have fixed most of my past issues with 5.7.15, raised a few centimetres higher the ColorVU and almost...

I would also try increasing I Frame Interval on Cameras settings(not through NVR) on Sub-Stream. You cannot do this on Main Stream if H265+ is enabled. But you can disable to experiment. You say that the image is grainy on the app. On NVR, there is also an option in Network-Advanced...

Did you also fix the Intrusion problem?

Hi Can you try the HiToolsDelivery for your Settings? The interface is similar to Edge

No, I went back to 5.7.15 once again. Seems that I am one of the few users of Playback by Rules. I do not use Search tab option and playback without the Rules option gives marks out of time on timeline. So this Rules option was the best at least for me and my NXI-K NVR. As I said before, maybe...